Spoil Pile Management
Reviewed by a working tradesman with 17+ years in the field.
Some links on this site are affiliate links. If you buy through them we may earn a commission at no extra cost to you. Affiliate disclosure
Where the dug-out soil goes, how big the pile gets, and which way water runs around it.
Tap your level and the boxes below open to the advice for you. Remembered on this device.
By the end you can
- Say why spoil is a load on the trench wall, and where it may not go.
- Work out the height and width of a pile from its volume.
- Keep water, machines and ladders clear of the pile.
- Keep topsoil, clean fill and suspect soil in separate piles.
- Know the stop-and-report steps for an archaeological find.
Never stack spoil at the edge of any hole that anyone will enter, and never drive or park on a spoil pile next to a trench. Spoil at the edge loads the wall, and the wall can let go with no warning. If a pile slumps toward the trench, get everyone out and move it before work continues.
The big idea
A pile of dirt next to a trench is a load sitting on the wall you are trying to keep standing. Where the pile goes, how big it gets and which way water runs around it all affect trench safety, your drainage, and whether you have clean material left for backfill.
Spoil setbacks come from your provincial OHS regulator, not from the building code, so they differ by province. NBC 2020 Part 9 sets no spoil setback.
How far back, and how much
- Where a pile sits next to a supported excavation, the shoring must be chosen to account for the extra side pressure from the pile.
- Alberta: spoil must be at least 1 m (3 ft 3 in) from the edge of the excavation to the leading edge of the pile, and the pile slope may not exceed 45 degrees from horizontal (OHS Code s. 453).
- Other provinces list distances close to this (see the By Province box). Treat 1 m as a floor, and go farther for deeper trenches and softer soil.
How tall will the pile be?
For a long pile with 45 degree sides (a windrow), the end view is a triangle with area h², so volume = h² × length. Example: 8 m³ of loose spoil in a 12 m (39 ft 4 in) windrow gives h² = 8 ÷ 12 = 0.667, so h = 0.82 m (2 ft 8 in), and the base is 2 × 0.82 = 1.63 m (5 ft 4 in) wide. With the nearest toe 1 m (3 ft 3 in) from the edge, the pile covers the ground from 1 m to 2.63 m (8 ft 8 in) back. Low and wide beats tall and narrow.
BC's spoil setback and the spoil allowance for shoring are in OHS Reg. Part 20 (s. 20.86 is titled Spoil piles). They were not read for this page. Until you have the number from the regulation, set spoil as far back as the site allows.
Where to put it
- On stable, level ground, well back from the edge and from any slope
- Away from ladders, walkways and the machine's travel path
- Away from existing structures, retaining walls and underground services
- Not where water naturally runs toward the hole
- Low and wide, with the sides at a stable angle
Water and spoil
- Do not let a pile dam a swale, block a drain or channel runoff into the trench
- Cover long-standing piles with poly or erosion blanket so rain does not turn them to mud
- Put silt fence or a straw wattle at the downhill toe of piles near drains or watercourses
Equipment
- Keep excavators, trucks and compactors off the edge. Machines load and vibrate the wall
- Never drive or park on a spoil pile next to a trench
- Never swing a bucket or load over workers
- Quebec's code keeps vehicles and machines 3 m (10 ft) from the rim unless the shoring is reinforced (summary). Check your own regulation for machines.
Keep your soils separate
- Strip topsoil and organics first and pile them on their own
- Keep clean granular material you plan to reuse apart from clay, silt and debris
- Set aside suspect or contaminated soil. Disposal of contaminated soil is regulated by the provinces
- Never mix organic soil back into bearing or backfill material
Soil relocation and contaminated-soil rules are provincial. Check the current requirements before moving soil off site.
If you find something in the ground
Digging can uncover bones, stone tools or other archaeological material. Stop work at that spot, leave it as you found it, protect it and report it. Do not move it or keep it.
- BC: do not disturb a find. Contact the Archaeology Branch, 250-953-3334, Archaeology@gov.bc.ca. For possible human remains, contact the Branch immediately and do not disturb them; the Branch notifies the Coroner and local police. Archaeological sites are protected whether or not they are known, and a permit is required before altering one.
- AB: developers must report a find to the Heritage Division under s. 31 of the Historical Resources Act.
- Everywhere else: contact your provincial or territorial archaeology or heritage office, and the police if you think the find is human.
If the land is within First Nations territory, the Nation can also have an interest in the find, and your permit conditions may name who to call.
Common mistakes
- Piles right at the trench edge
- Tall, steep piles on soft ground
- Piles that block the ladder or the exit route
- Piles that send runoff into the hole
- Topsoil, clay and clean gravel all mixed in one heap
Decide on the spoil plan before the first bucket comes out. If there is no room on site, truck it away and bring clean material back. It costs less than a shoring redesign or a collapsed wall.
Rain makes spoil slump and slide toward the trench. Snow on a pile hides how big it is. Frozen lumps do not compact when you reuse them. Check piles after storms and freeze-thaw cycles.
Spoil placement is a worker-safety issue before it is a building-inspection issue. OHS officers can stop work where spoil adds load to an unsupported or shored excavation.
Alberta sets spoil at least 1 m back from a trench edge. How far is that in feet and inches?
You have 8 m³ of loose spoil to place in a 12 m (39 ft 4 in) windrow with 45 degree sides. How tall will it be?
Why can the same pile be fine at 1 m back on a firm site and a problem on a soft one?
The spoil pile is on the uphill side of the hole and rain is coming. What is the problem?
You uncover what looks like bone and a stone tool. What do you do?
Can you mix topsoil back in with your clean gravel backfill pile?
- Rent itMoving soil by machine: an excavator or skid steer with a skilled operator
- Must-haveMoving soil by hand:
- Must-haveMarking the setback:
- Must-haveCovering and containing:
- Must-haveKeeping soils separate:
- Must-haveChecking slopes: a 4 ft (1.2 m) level and a tape to check pile height and angle after storms
- Must-havePPE:
Home DIY
Laborer or helper
1st-year apprentice
Apprentice, 2nd to 4th year
Journeyperson
Lead hand or foreman
Contractor or business owner
Starting a new business
No national code sets a spoil setback. Each OHS regulation does, and the distances are close but not identical. Figures marked (summary) come from a secondary compilation, so check them in the regulation.
- BC: setback and the shoring allowance for spoil are in OHS Reg. Part 20, s. 20.86. Confirm.
- AB: at least 1 m (3 ft 3 in), pile slope 45 degrees or less (s. 453).
- SK, NWT, NU: 1 m (summary). ON: 1 m, O. Reg. 213/91 (see Trench Safety).
- QC: 1.2 m (4 ft) from the rim, vehicles 3 m (10 ft) back unless reinforced shoring (summary).
- NB: 1.2 m. NS: at least 1 m unless an engineer certifies less. PE: 2 ft (609 mm). NL: 1.22 m for trenches (all summary).
- MB, YT: confirm with the regulator.
See Canada by Province for the full comparison.
- Alberta OHS Code Explanation Guide, Part 32 (s. 453, spoil piles; the 2009 guide)
- OHS Insider, Excavation and trenching: know the laws of your province (secondary compilation for the other provinces)
- BC Archaeology Branch, Report a find
- Alberta, Report an archaeological find
- WorkSafeBC, OHS Regulation Part 20 (section titles)
Last reviewed October 2026. General information, not engineering or legal advice. Check the current regulation.
